Arduino

Intro-Arduino.adoc

@@ -27,11 +27,11 @@ https://en.wikipedia.org/wiki/Arduino[^]
 
 The 14 digital input/output pins can be used as input or output pins by using pinMode(), digitalRead() and digitalWrite() functions in arduino programming. Each pin operate at 5V and can provide or receive a maximum of 40mA current, and has an internal pull-up resistor of 20-50 KOhms which are disconnected by default.  Out of these 14 pins, some pins have specific functions as listed below:
 
-    Serial Pins 0 (Rx) and 1 (Tx): Rx and Tx pins are used to receive and transmit TTL serial data. They are connected with the corresponding ATmega328P USB to TTL serial chip.
-    External Interrupt Pins 2 and 3: These pins can be configured to trigger an interrupt on a low value, a rising or falling edge, or a change in value.
-    PWM Pins 3, 5, 6, 9 and 11: These pins provide an 8-bit PWM output by using analogWrite() function.
-    SPI Pins 10 (SS), 11 (MOSI), 12 (MISO) and 13 (SCK): These pins are used for SPI communication.
-    In-built LED Pin 13: This pin is connected with an built-in LED, when pin 13 is HIGH – LED is on and when pin 13 is LOW, its off.
+    - Serial Pins 0 (Rx) and 1 (Tx): Rx and Tx pins are used to receive and transmit TTL serial data. They are connected with the corresponding ATmega328P USB to TTL serial chip.
+    - External Interrupt Pins 2 and 3: These pins can be configured to trigger an interrupt on a low value, a rising or falling edge, or a change in value.
+    - PWM Pins 3, 5, 6, 9 and 11: These pins provide an 8-bit PWM output by using analogWrite() function.
+    - SPI Pins 10 (SS), 11 (MOSI), 12 (MISO) and 13 (SCK): These pins are used for SPI communication.
+    - In-built LED Pin 13: This pin is connected with an built-in LED, when pin 13 is HIGH – LED is on and when pin 13 is LOW, its off.
 
 Along with 14 Digital pins, there are 6 analog input pins, each of which provide 10 bits of resolution, i.e. 1024 different values. They measure from 0 to 5 volts but this limit can be increased by using AREF pin with analog Reference() function.  
 
@@ -39,8 +39,8 @@ Along with 14 Digital pins, there are 6 analog input pins, each of which provide
 
 Arduino Uno has a couple of other pins as explained below:
 
-    AREF: Used to provide reference voltage for analog inputs with analogReference() function.
-    Reset Pin: Making this pin LOW, resets the microcontroller.
+    - AREF: Used to provide reference voltage for analog inputs with analogReference() function.
+    - Reset Pin: Making this pin LOW, resets the microcontroller.
 
 == Communication
 

Intro-IoT.adoc

@@ -13,6 +13,7 @@ Apostolos rootApostolos@swarmlab.io
 
 {empty} +
 
+
 Ορισμός, βασικά χαρακτηριστικά και αρχιτεκτονικές IoT, εφαρμογές ΙοΤ, αντιδιαστολή με τον ιστό των αντικειμένων (Web of Things / WoT), προκλήσεις του IoT όπως προτυποποίηση, κλιμάκωση, μέγεθος συσκευών, κατανάλωση ενέργειας, διευθυνσιοδότηση, ασφάλεια/ιδιωτικότητα, ποιότητας υπηρεσιών, κινητικότητα κ.α
 
 Δομή και τεχνολογία κόμβων. Αρχιτεκτονική και τοπολογίες. Πρότυπα και πρωτόκολλα φυσικού επιπέδου. Θέματα διανομής, επικοινωνίας και οργάνωσης. Πρωτόκολλα δρομολόγησης. Ενεργειακά αποδοτικοί αλγόριθμοι συλλογής και επεξεργασίας δεδομένων.